Allg. Hinweise zum Update Zur Durchführung des Updates benötigen Sie eine Netzwerkverbindung zwischen Ihrem Computer und dem Wechselrichter. Geben Sie in Ihren Browser die IP-Adresse des Wechselrichters ein und wählen Sie nach erfolgreichem Login im Menü unter "Servicemenü" den Punkt "Update" aus. Folgen Sie den dort stehenden Anweisungen. Falls gewünscht können Sie vor dem Update die Logdaten sichern, indem Sie diese direkt von der Webapp herunterladen, oder zu einem Solar Portal übertragen. Nach Übertragung und Durchführung des Update, müssen Sie das Gerät über den Button in der Webapp neu starten. Im Anschluss an ein erfolgreiches Update startet der Wechselrichter in den regulären Betriebsmodus. Sollte dies nicht der Fall sein, schalten Sie den Wechselrichter bitte 2 Minuten DC- und AC-Seitig spannungsfrei und nehmen das Gerät danach wieder in Betrieb. Datum (JJJJ.MM.TT): 2025.03.20 KOSTAL_Update_PLENTICORE_G3_3.04.02.18459 Änderungen - Menü "Energiemanagement" umbenannt in "Netzanschluss" - Neu: Batterie kann mit dyn. Stromtarif geladen werden. (Neues Menü "Batterienutzung") - Neu: Kuppelschalterfunktion ist im Menü "CEI/VDE" auswählbar - Optimierung Startverhalten - Batterie-Ruhemodus kann abgeschaltet werden. (Verbessert die Bereitschaft für Backup-Betrieb) - Fehler in Statistikdaten bei Betrieb als reiner PV-Wechselrichter wurde behoben. - Die Einstellungen für den Backup-Betrieb werden nur angezeigt, wenn diese Betriebsart konfiguriert wurde. - Webmenü: Solar Portal Meldung Popup nur anzeigen, wenn die Verbindung gestört ist. - Die Deaktivierung der Typ-A Kompatibilitätsüberwachung wurde nicht dauerhaft gespeichert. Nach einem Neustart war die Überwachung wieder aktiv. - Korrektur für Zeitgesteuerte Batterieladung, Modus "Laden aus dem Netz, keine Entladung bei Hausverbrauch" - Neue Länderparametersätze CY EAC 2025 DK1 TF3.3.1 Rev.5 Type A DK2 TF3.3.1 Rev.5 Type A FI SFS-EN50549-1 YA9:23 LT ESO A0 2023 PL PTPiREE 2024 Type A Datum (JJJJ.MM.TT): 2025.02.10 KOSTAL_Update_PLENTICORE_G3_3.04.01.17931 Änderungen - Korrektur WLAN-QR-Code - Bugfix Schaltausgänge - Korrektur für Geräte ohne Update auf SW 03.04.01.17734 : Für den Alternativen Zeitraum wird der min. SoC des Standardzeitraums übernommen - Hinweistexte für SoC-Einstellungen im Menübereich "Backup-Betrieb" ergänzt: Bedeutung des Entlade-SoC und Start-SoC - Anpassung Einstellungen für den Backup-Betrieb: Die Hysterese zwischen Start-SoC und Entlade SoC muss 1% betragen anstatt 5%. D.h. Start-SoC >= Entlade-SoC+1% Datum (JJJJ.MM.TT): 2025.01.14 KOSTAL_Update_PLENTICORE_G3_3.04.01.17734 Änderungen - Neue Länderparametersätze (auf Basis der EN50549-1) BE C10/11 2019 LV CY EAC 2023.2 DE VDE4105 Batterie DK1 GPD 2022 Type A LV DK2 GPD 2022 Type A LV EE EN50549-1 Type A FR NF EN 50549-1 GR RFG Type A Main GR RFG Type A Islands LV Sadales Tikls Type A LT ESO A0 2023 NL EN50549-1 2019 NO EN50549-1 2019 PT EN50549-1 2019 SE EIFS2018-2 EN50549-1 2019 IEC61727 / 62116 - Neues Webdesign - Ergänzung der Batterieeinstellungen für Backupbetrieb - Alternativer Zeitraum für min. SoC (z.B. Vorhaltung einer größeren Backup-Reserve im Winter): Standard-Einstellung für den Zeitraum ist der 1.11. bis 28.2. mit einem min. SoC von 20%. Es kann im Webmenü unter "Alggemein" --> Batterieeinstellungen" geändert werden - Entlade-SoC: Während des Backup-Betriebs wird der Speicher bis auf diesen SoC entladen. - Start SoC: Wenn der Speicher ist auf den Entlade-SoC entladen wurde, wird zuerst auf den „Start-SoC“ aufgeladen, bevor der Backup-Betrieb wieder aufgenommen wird. - Über das Displaymenü kann bei aktiviertem WLAN-AccessPoint ein QR-Code mit den Verbindungsdaten angezeigt werden. - Neuer Modus für die Digitaleingänge: „Leistungsbegrenzung nach §14a EnWG“ (Begrenzung der Aufnahmeleistung auf 4,2kW via FNN-Steuerbox) - EEBus erstmalig verfügbar - Der Wechselrichter stellt seine Momentanwerte zwecks Monitoring bereit (use cases MOI, MOB, MPC) - Der Wechselrichte rkann durch ein externes System gesteuert werden (use cases LPP und LPC) - Optimierung der Vertauschungserkennung (DC-Anschlüsse) - Geräteschlüssel/Erweiterte Batterieinformationen werden ans Portal übertragen. - Bugfix: Das Register 588d "Battery Type" im Modbus TCP wurde korrigiert von u32 auf u16. - Bugfix: Die Konfiguration der Zeitsteuerung der Schaltausgänge wird nun korrekt abgespeichert. - Div. Fehlerbehebungen und Verbesserungen Datum (JJJJ.MM.TT): 2024.08.14 KOSTAL_Update_PLENTICORE_G3_3.04.00.16312 Änderungen - Unterstützung Speichersystem "VARTA.wall" - Unterstützung Speichersystem "ZYC" - AutoIP-Funktionalität hinzu - Zeitgesteuerte Batterienutzung mit neuem Modus "Batterieladung mit Netzbezug" - Einschwingzeit kann nun alternativ auch in W/s eingegeben werden. - Status "Schwachlicht" umbenannt in "DC Check" - Optimierungen Kommunikation WR <-> Batteriesystem - Div. Fehlerbehebungen und Verbesserungen Datum (JJJJ.MM.TT): 2024.06.12 KOSTAL_Update_PLENTICORE_G3_3.03.22.15980 Änderungen - Initiales Release für PLENTICORE M G3 - Ursache für EC1080 behoben - Verbesserung Stabilität - Div. Bugfixe Datum (JJJJ.MM.TT): 2024.05.08 KOSTAL_Update_PLENTICORE_G3_3.03.21.15638 Änderungen - Verbesserung Stabilität - Div. Bugfixe --------------------------------------------------------------------------------------- Installation notices To perform the update, you need a network connection between your computer and the inverter. Enter the IP address of the inverter in your browser and after successful login, select in the menu under "Service menu" => "Update". Follow there the instructions. If required, you can save the log data before the update, by downloading it directly from the Webapp or send it to the Piko Solar Portal. After transfer and execution of the update, you must restart the device via the button in the Webapp. Following a successful update, the inverter starts to regular operation mode. If this is not the case, turn the inverter off by disconnecting DC and AC-side for two minutes and then back into operation. Date(JJJJ.MM.TT): 2025.03.20 KOSTAL_Update_PLENTICORE_G3_3.04.02.18459 Changes - "Energy management" menu renamed "Grid connection" - New: Battery can be charged at a dynamic electricity tariff. (New “Battery usage” menu) - New: Coupling switch function can be selected in the ‘CEI/VDE’ menu - Optimisation of start-up behaviour - Battery sleep mode can be switched off. (Improves readiness for backup operation) - Error in statistical data when operating as a pure PV inverter has been fixed. - The settings for backup operation are only displayed if this operating mode has been configured. - Web menu: Solar Portal message popup only when the connection is interrupted. - Deactivating type-A compatibility monitoring was not saved permanently. After a restart, monitoring was reactivated. - Correction for time-controlled battery charging, mode ‘Charge from the grid, do not discharge when household consumption occurs’ - New country parameters sets CY EAC 2025 DK1 TF3.3.1 Rev.5 Type A DK2 TF3.3.1 Rev.5 Type A FI SFS-EN50549-1 YA9:23 LT ESO A0 2023 PL PTPiREE 2024 Type A Date(JJJJ.MM.TT): 2025.02.10 KOSTAL_Update_PLENTICORE_G3_3.04.01.17931 Changes - Correction of Wi-Fi QR code - Bugfix switching outputs - Correction for devices without update to SW 03.04.01.17734 : For the alternative time period, the min. SoC of the standard time period is adopted - Added information texts for SoC settings in the ‘Backup operation’ menu: meaning of discharge SoC and start SoC - Adjustment of settings for backup operation: the hysteresis between start SoC and discharge SoC must be 1% instead of 5%. I.e. start SoC >= discharge SoC+1% Date(JJJJ.MM.TT): 2025.02.06 KOSTAL_Update_PLENTICORE_G3_3.04.01.17931 Changes - Bugfix: Incorrect display of the WLAN QR code - Bugfix Switching outputs: Without an energy meter, the selection ‘Switching based on PV power’ could not be saved. - Bugfix Switching outputs: Under certain circumstances, output 3 could assume an incorrect state. - Correction: The default value for the min. SoC of the ‘Alternative period’ is now 5%. - Correction: For existing devices that have not yet received an update with SW 03.04.01.17734, the min. SoC of the standard period is adopted for the alternative period. - Added information texts for SoC settings in the ‘Backup operation’ menu: Meaning of discharge SoC and start SoC - Correction of settings for backup operation: The hysteresis between start SoC and discharge SoC must be 1% instead of 5%. I.e. Start SoC >= Discharge SoC+1% Known bugs: - Seltest Italy CEI > 11kW returns empty values: This is not critical because an external grid and system protection is required for systems > 11kW. This will be fixed in 3.04.02. Date(JJJJ.MM.TT): 2025.01.14 KOSTAL_Update_PLENTICORE_G3_3.04.01.17743 Changes - New country parameter sets (based on EN50549-1) BE C10/11 2019 LV CY EAC 2023.2 DE VDE4105 Batterie DK1 GPD 2022 Type A LV DK2 GPD 2022 Type A LV EE EN50549-1 Type A FR NF EN 50549-1 GR RFG Type A Main GR RFG Type A Islands LV Sadales Tikls Type A LT ESO A0 2023 NL EN50549-1 2019 NO EN50549-1 2019 PT EN50549-1 2019 SE EIFS2018-2 EN50549-1 2019 IEC61727 / 62116 - New web design - Addition of battery settings for backup operation - Alternative period for min. SoC (e.g. provision of a larger backup reserve in winter): The standard setting for the period is 1 November to 28 February with a minimum SoC of 20%. It can be changed in the web menu under ‘General’ --> ‘Battery settings’. - Discharge SoC: During backup operation, the storage system is discharged down to this SoC. - Start SoC: If the storage system has been discharged to the discharge SoC, it is first charged to the ‘Start SoC’ before backup operation is resumed. - During web-based initial commissioning, the AutoUpdate is already preselected (same as for display-based commissioning). - A QR code with the connection data can be displayed via the display menu when the WLAN AccessPoint is activated. - New mode for the digital inputs: ‘Power limitation according to §14a EnWG’ (limitation of the input power to 4.2kW via FNN control box) - EEBus available for the first time - The inverter provides its instantaneous values for monitoring (use cases MOI, MOB, MPC) - The inverter can be controlled by an external system (use cases LPP and LPC) - Optimisation of the polarity reversal detection (DC connections) - Device key/extended battery information is transmitted to the portal. - Bugfix: Register 588d ‘Battery Type’ in Modbus TCP has been corrected from u32 to u16. - Bugfix: The configuration of the time control of the switching outputs is now saved correctly. - Various bug fixes and improvements Date(JJJJ.MM.TT): 2024.08.14 KOSTAL_Update_PLENTICORE_G3_3.04.00.16312 Changes - Support for ‘VARTA.wall’ storage system - Support for ‘ZYC’ storage system - AutoIP functionality added - Time-controlled battery use with new ‘grid-sourced battery charging’ mode - Settling time can now alternatively be entered in W/s - Status ‘Low light’ renamed to ‘DC Check’ - Optimisation of communication between inverter <-> battery system - Various bug fixes and improvements Date(JJJJ.MM.TT): 2024.06.12 KOSTAL_Update_PLENTICORE_G3_3.03.22.15980 Changes - Initial Release for PLENTICORE M G3 - Root cause for EC1080 fixed - Improving stability - Several Bugfixes Date(JJJJ.MM.TT): 2024.05.08 KOSTAL_Update_PLENTICORE_G3_3.03.21.15638 Changes - Improving stability - Several Bugfixes