Allg. Hinweise zum Update Zur Durchführung des Updates benötigen Sie eine Netzwerkverbindung zwischen Ihrem Computer und dem Wechselrichter. Geben Sie in Ihren Browser die IP-Adresse des Wechselrichters ein und wählen Sie nach erfolgreichem Login im Menü unter "Servicemenü" den Punkt "Update" aus. Folgen Sie den dort stehenden Anweisungen. Falls gewünscht können Sie vor dem Update die Logdaten sichern, indem Sie diese direkt von der Webapp herunterladen, oder zu einem Solar Portal übertragen. Nach Übertragung und Durchführung des Update, müssen Sie das Gerät über den Button in der Webapp neu starten. Im Anschluss an ein erfolgreiches Update startet der Wechselrichter in den regulären Betriebsmodus. Sollte dies nicht der Fall sein, schalten Sie den Wechselrichter bitte 2 Minuten DC- und AC-Seitig spannungsfrei und nehmen das Gerät danach wieder in Betrieb. Datum (JJJJ.MM.TT): 2024.02.21 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.30.12092 Änderungen - Aktivierung Switching Overvoltage bei LVRT/HVRT - Anfahrrampe nach Inselnetzerkennung - Bugfix: Bugfix Abschaltreihenfolge PWM / AC Relays - Bugfix P(f) Überfrequenz: Werte für Statik und Gradient werden nicht richtig in den Parametrierungsbericht geschrieben. Datum (JJJJ.MM.TT): 2023.09.27 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.29.12038 Änderungen - Bufix: Nach Netzfehlern konnte bei bestimmten Bedingungen vorkommen, dass ein WR erst nach 1 Stunde wieder aufs Netz schaltet. - Fehlauslösungen EC5066 behoben - Korrektur Darstellung Hausverbrauch bei Werten > 38kW Datum (JJJJ.MM.TT): 2023.07.10 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.28.10771 Änderung - Batteriesystem "Dyness Tower" ist freigegeben und im Menü auswählbar. Datum (JJJJ.MM.TT): 2023.04.21 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.27.09932 Änderungen - Batteriesysteme Wintersun, Pylontech Force H1/H2 und AxiStorage Li SV1/SV2 freigegeben und im Menü auswählbar Datum (JJJJ.MM.TT): 2023.02.08 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.26.09454 Änderungn Die Einstellung der Wirkleistungsbegrenzung ist nun auch für den Anlagenbesitzer möglich. ACHTUNG: Der Anlagenbetreiber ist verantwortlich für die korrekte Einstellung der Wirkleistungsbegrenzung. Die für Ihre Anlage zulässige Wirkleistung nennt Ihnen Ihr Netzbetreiber. TIPP: Wir empfehlen, alle Einstellungen durch den Installateur vornehmen zu lassen. Datum (JJJJ.MM.TT): 2022.11.28 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.25.09070 (FW01.76) Änderungen - Bugfix Schttenmanagement: Es konnte bei akt. Schattenmanagement dazu kommen, dass die Batterie bis zum nächsten Tag nicht geladen oder nicht genutzt wurde. - Bugfix: Es konnte dazu kommen, dass Ereigniscode 5076 auftrat, der zu kurzzeitigen Abschaltungen des Gerätes führte. Der Regelalgorithmus wurde entsprechend angepasst. Datum (JJJJ.MM.TT): 2022.09.29 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.24.08775 (FW01.75/PAR03.55) Änderungen - KOSTAL Energy Meter Serie P als Energiezähler im Auswahlmenü hinzu "KEM-P" - Im Auswahlmenü "KEM" geändert in "KEM-C" (Serie C) - Kompatibilität zu Speichersystem LG Resu flex - Bugfix: Mobus TCP Register 517, 525, 527 und 586 werden wieder korrekt befüllt. - Bugfix: Externe Batteriesteuerung wird beim Abwaehlen der Batterie ausgeschaltet. - Trotz Systemenergie Überschuss (aktivierte ext. Überschussladung) wurde teilweise, bei nicht vorhandener PV-Energie, die Batterie nicht geladen. Diese Verhalten wurde korrigiert und abgestellt. - Bugfix EC 5076 PC BI: Insbesondere bei ungünstigen Netzbedingungen konnte es beim BI-10-26 insbesondere bei abrupten Leistungsänderungen (Übergang zu SoC min oder zu SoC 100%) zur kurzzeitigen Abschaltung des WR kommen (Ereigniscode 5076). Dieses Verhalten konnte durch eine Funktionsverbesserung softwareseitig abgefangen werden. - KEM-C: Bugfix der Hausverbrauchsvisulalisierung bei nicht vorhandener DC Energie (Hausverbrauch bei Nacht wurde nicht ermittelt und dargestellt, Portal und Web-App) - Weitere interne Verbesserungen Datum (JJJJ.MM.TT): 2022.06.20 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.23.07734 (FW01.70/PAR03.55) Änderungen - Anzeige "---" für Hausverbrauch im Display, wenn 0W Hausverbrauch anliegen bzw. kein Leistungsmessgerät angeschlossen ist. - Bonjour Service um Zusatzinfos ergänzt (Key: ScbWebApi, Value: v1). - Eintrag „AXITEC“ im Batterie-Auswahlmenü geändert zu „AXIstorage Li SH“ - Interne Verbesserungen Datum (JJJJ.MM.TT): 2022.03.30 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.22.06892 (FW01.65/PAR03.50) Änderungen - Bugfix 0-Watt Abregelung - Bugfix Abwählen der intelligenten Batteriesteuerung nach dem Update auf FW >= 01.60 - RfG-Anforderungen für Spanien umgesetzt, Parametersatz "ES RD647 Type A" - Entfernung der Auswahl von veralteten Parametersätzen Datum (JJJJ.MM.TT): 2022.02.16 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.21.06586 (FW01.60/PAR03.44) Änderungen - Neues Verhalten des Ruhemode: - Bei Entladung auf den konfigurierten min. SoC wird die Trennstelle des Speichersystems geöffnet. - Sofortiges Aufwachen aus dem Ruhemode und Zuschalten der Batterie, sobald Überschussleistung zur Ladung vorhanden ist oder Ladung durch externe Steuerung angefordert wird. - Batterie-Notladung: Autom. Erhöhung des Delta-SoCs auf bis zu 15%, wenn während einer Schlechtwetterperiode die Batterie nicht geladen werden kann. Dadurch werden die Notlade-Vorgänge minimiert. - Serviceladung auf 100% kann in den Batterieeinstellungen des Webmenüs gestartet werden. (Nur mit Installateurs-Login möglich.) - PLENTICORE BI 10/26: CEI 0-16 und CEI 0-21 in den Ländereinstellungen hinzu Datum (JJJJ.MM.TT): 2021.08.05 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.20.05838 (FW01.57/PAR03.39) Änderungen - Fix PLENTICORE BI und Nilar (Regelungsanpassung bei großen Ladestrom-Änderungen) Datum (JJJJ.MM.TT): 2021.06.24 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.20.05778 Änderungen - Fix: Mögliche Verwendung falscher Werte in der Leistungsflussdarstellung. Datum (JJJJ.MM.TT): 2021.06.24 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.20.05774 Änderungen - Speichersysteme „BMZ“ und „AXITEC“ werden nun unterstützt und sind in den Batterieeinstellungen auswählbar. - Optimierung Selbsttest Italien CEI 0-21 - PL 50549-1 Frequenzparameter 49.0Hz <= f <= 50.05Hz - PL 50549-1 für PLENTCIORE BI verfügbar - Aktuelle Netzanschlussrichtlinie Schweiz hinzu („CH NA/EEA 2020 A2“) Datum (JJJJ.MM.TT): 2021.04.16 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.19.05650 Änderungen - Korrektur Sunspec-Register (relevant für Varta AC-Speicher) - Neues Speichersystem "Nilar Home Box" ist kompatibel - BI 5.5/26 und 10/26: Belgien in der Länderauswahl ergänzt Datum (JJJJ.MM.TT): 2021.01.29 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.18.05255 Änderungen - Die Funktion AutoUpdate ist nun verfügbar. Es kann gewählt werden zwischen „manuellem Update per Dateiupload“ / „über verfügbare Updates informieren“ / „Updates automatisch durchführen“. Ändern Sie hierzu nach erfolgter Softwareaktualisierung im Updatemenü des Webservers die Updatemethode. - PLENTICORE BI 5.5/26 und 10/26: Die zur Verfügung stehenden Länderparametersätze wurde ergänzt. Folgende Parametersätze sind verfügbar: Land/Country Ländereinstellungen/Display Austria AT TOR Gen. Type A LV Switzerland CH NA/EEA 2014 Germany DE VDE4105 cosphi=1 Denmark DK TF3.3.1 DK1 Type A Denmark DK TF3.3.1 DK2 Type A Spain ES RD1699 RD431 Isl. Spain ES RD1699 RD431 Main Finland FI VJV2018 Type A France FR VFR2019 Greece GR RFG Type A Main Greece GR RFG Type A Islands Latvia LV EN50549-1 2019 Netherlands NL EN50549-1 2019 <11kW Netherlands NL EN50549-1 2019 >11kW Norway NO EN50549-1 2019 Portugal PT EN50438 2013 Portugal PT EN50549-1 2019 Sweden SE EIFS2018-2 Standard EN50438 2013 Standard EN50549-1 2019 Standard G98/1-4 Standard G99/1-6 LV Standard VDE 4100/4105 Datum (JJJJ.MM.TT): 2020.11.20 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.17.05075 Änderungen - Anpassungen von Übersetzungen - Änderung/Abspeicherung des Menüs "Batteriesteuerung" ist nur für Rolle Installateur möglich - Min. Ladezustand "Dynamisch" war bei aktivierter "Intelligente Batteriesteuerung aktivieren" nicht auswählbar Datum (JJJJ.MM.TT): 2020.11.04 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.16.05025 Änderungen - Neue Möglichkeit externe Batteriesteuerung via Modbus (Einrichtung nur mit Servicecode) - Neue Möglichkeit externe Batteriesteuerung via Digitale Eingänge (Einrichtung nur mit Servicecode) - Implementierung zusätzlicher Modbus Statistik Datenpunkte - Implementierung Umschaltmöglichkeit Modbus little zu big-endian - Implementierung "Zeitgesteuerte Batterienutzung" (auch durch Endkunden) - Erste Version für PLENTICORE BI 5.5/26 und 10/26 Bugfixes - Anzeigefehler Lüfteransteuerung - Regelungsoptimierungen - Ergänzungen zur Erfüllung der Modbus Sunspec Anforderungen (Lesen/Schreiben) Datum (JJJJ.MM.TT): 2020.05.29 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.15.04581 - Rücknahme der Bytereihenfolge im Modbus von CDAB zu ABCD Datum (JJJJ.MM.TT): 2020.05.20 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.15.04529 Änderungen - Notwendige Anpassungen für BYD Premium Batterie HVS 5.1 bzgl. der Batteriespannung - Änderung Bytereihenfolge im Modbus von CDAB zu ABCD - Umsetzungen weiterer Ländereinstellungen GR RFG Type A Main GR RFG Type A Islands CZ PPDS 2018 <16A CZ PPDS 2018 >16A Datum (JJJJ.MM.TT): 2020.02.20 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.14.04213.swu UI-Änderungen - Allgemeine Optimierungen - Bugfix - Bildschirmschoner zeigte Netzleistung statt Einspeiseleistung - Bugfix DC-Leistung wurde im Display unter bestimmten Bestimmungen nicht mehr angezeigt - Erste Version für PLENTICORE BI 5.5/26 und 10/26 Datum (JJJJ.MM.TT): 2019.12.17 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.13.04122.swu FW-Änderungen - Umsetzungen weiterer Ländereinstellungen Land/Country Ländereinstellungen/Display Austria AT TOR D4 2016 LV Austria AT TOR Gen. Type A LV Belgium BE C10/11 2019 LV Switzerland CH NA/EEA 2014 Switzerland CH VDE4105 2011 Cyprus CY EN50438 2013 Czech Republic CZ EN50438 2013 Germany DE VDE4105 cosphi=1 Germany DE VDE4105 cosphi(P) Germany DE VDE4105 Q(U) Denmark DK RFG LV DK1 Type A Denmark DK RFG LV DK2 Type A Denmark DK TF3.2.1 2016 Estonia EE EN50549-1 Type A Spain ES RD1699 RD431 Main Spain ES RD1699 RD431 Isl. Finland FI EN50438 2013 Finland FI VJV2018 Type A France FR VFR2014 France FR VFR2019 Greece GR VDE0126 PPC Main Greece GR VDE0126 PPC Islands Italy IT CEI0-21 2017 <11kW Italy IT CEI0-21 2019 <11kW Italy IT CEI0-21 2019 >11kW Jordan JO G59/3-3 LV Jordan JO G83/2 Latvia LV EN50438 2013 Netherlands NL EN50438 2013 Norway NO EN50438 2013 Poland PL EN50438 2013 Poland PL EN50549-1 2019 Portugal PT EN50438 2013 Portugal PT EN50438 2013 3.45kW Portugal PT EN50438 2013 3.68kW Sweden SE EIFS2018-2 Sweden SE EN50438 2013 United Kingdom UK G98/1-3 United Kingdom UK G99/1-4 LV Standard CEI0-21 2017 <11.08kW Standard CEI0-21 2017 >11.08kW Standard CEI0-21 2019 <11.08kW Standard CEI0-21 2019 >11.08kW Standard EN50438 2013 Standard EN50549-1 2019 Standard G59/3-3 LV Standard G83/2 Standard G98/1-3 Standard G99/1-4 LV Standard IEC61727 / 62116 Standard VDE 0126-1-1 Standard VDE 4105 2011 Standard VDE 4105 2018 - Schnellere Eigenverbrauchsregelung - FW für den KOSTAL Smart Energy Meter in 2020 verfügbar Bugfixes - Optimierungen bezüglich Batterieentladungen - Optimierungen am Schattenmanagement Algorithmus bei niedrigen PV Spannungen - Optimierungen im LVRT Modus UI-Änderungen - Über das Menü kann nun der manueller Lüftertest gestartet werden - Allgemeine Optimierungen Datum (JJJJ.MM.TT): 2019.08.09 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.11.03557 Bugfix - Fehlende Anzeige der Länderauswahl für VDE0126, Austria und VDE4105 wird wieder angezeigt Folgende Länderauswahl steht nun im Gerät zur Verfügung. Land/Country Ländereinstellungen/Display Austria - AT TOR D4 2016 LV Cyprus - CY EN50438 2013 Czech Republic - CZ EN50438 2013 Germany - DE VDE4105-cosphi=1 Germany - DE VDE4105-cosphi(P) Germany - DE VDE4105-Q(U) Denmark - DK TF3.2.1 2016 Spain - ES RD1699 RD413 Islands Spain - ES RD1699 RD431 Main Finland - FI EN50438 2013 France - FR VFR2014 France - FR VFR2019 Greece - GR VDE0126 PPC Main Greece - GR VDE0126 PPC Islands Italy - IT CEI0-21 2017 <11kW Jordan - JO G83/2 Jordan - JO G59/3-3 LV Latvia - LV EN50438 2013 Netherlands - NL 50438 2013 Norway - NO EN50438 2013 Poland - PL EN50438 2013 Portugal - PT EN50438 2013 Sweden - SE EN50438 2013 Switzerland - CH NAIEEA 2014 Switzerland - CH VDE 4105:2011 United Kingdom - UK G98/1-3 Standard - CEI0-21:2017 <11.08kW Standard - G59/3-3 - LV Standard - G83/2 Standard - G98/1-3 Standard - EN 50438:2013 Standard - IEC61727 / 62116 Standard - VDE 0126-1-1 Standard - VDE 4105:2011 Standard - VDE 4105:2018 Datum (JJJJ.MM.TT): 2019.07.29 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.11.03546 FW-Änderungen - Feature: Manuelle Lüfterprüfung über das Display wurde freigeschaltet - Feature: Erweiterung der Modbus Register - weitere Batteriedaten - Feature: G98-Trip neue Konfigurierbarkeit für Trip-Funktion über den Webserver - Feature: Steuerung der Q(U) Verschiebungsfaktoren - Darstellung: Hinweis auf cos phi = 1 bei deaktivierter Blindleistung - Optimierung: Intelligente Batteriesteuerung (Ertrags-Lastprognose) wurde optimiert - Bugfix:"Fehlender Richtlinienanzeigetext" wird angezeigt - Bugfix: Aufschalten nach auftretenden Events - Stichwort Aufschalten nach 5060 Datum (JJJJ.MM.TT): 2019.06.13 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.09.03412.swu Bugfix - Korrektur fehlerhafter Lüfter-Event Ablagen Datum (JJJJ.MM.TT): 2019.04.30 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.07.03318.swu UI - Anpassungen Lizenztexte Datum (JJJJ.MM.TT): 2019.04.26 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.07.03311.swu UI Änderungen - Umbenennung/Ergänzung der Ländereinstellungen Austria - AT TOR D4 2016 LV Cyprus - CY EN50438 2013 Czech Republic - CZ EN50438 2013 Germany - DE VDE4105-cosphi=1 Germany - DE VDE4105-cosphi(P) Germany - DE VDE4105-Q(U) Denmark - DK TF3.2.1 2016 Spain - ES RD1699 RD413 Islands Spain - ES RD1699 RD431 Main Finland - FI EN50438 2013 France - FR VFR2014 France - FR VFR2019 Greece - GR VDE0126 PPC Main Greece - GR VDE0126 PPC Islands Italy - IT CEI0-21 2017 <11.08kW Jordan - JO G83/2 Jordan - JO G59/3-3 LV Latvia - LV EN50438 2013 Netherlands - EN50438 2013 Norway - NO EN50438 2013 Poland - PL EN50438 2013 Portugal - PT EN50438 2013 Sweden - SE EN50438 2013 United Kingdom - UK G98/1-3 Standard - CEI0-21:2017 <11.08kW Standard - G59/3-3 - LV Standard - G83/2 Standard - G98/1-3 Standard - EN 50438:2013 Standard - IEC61727 / 62116 Standard - VDE 0126-1-1 Standard - VDE 4105:2011 Standard - VDE 4105:2018 - Features: - Wechselrichter startet selbsttätig nach Rücksetzen der Länderrichtlinie neu - Integration des Button Batteriemode zurücksetzen in der Webapp - Eventcodeliste inkl. Übersetzungen aktualisiert - Neue Batteriegrößen über Modbus zur Verfügung gestellt Battery Type (Modbus Register 588) Manufacturer (Modbus Register 517) ModelName (Modbus Register 525) SerialNumber (Modbus Register 527) WorkACOut (Modbus Register 110) PowerACIn (Modbus Register 280) Bruttokapazität (Modbus Register 529) Status (Modbus Register 104) Firmware (Modbus Register 586) - Überarbeitete Übersetzungen eingefügt - Anzeige des Wechselrichter/Batteriestatus in der Webapp - Anpassung der Update Seite - Low-Priority Wirkleistungssteuerung per Modbus hinzugefügt - Bugfixes: - Darstellung Eventliste - Mobil optimiert Datum (JJJJ.MM.TT): 2019.03.27 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.05.03190 FW-Änderungen - Feature: Implementierung des Sony/MURATA- Batteriesystems für PLENTICORE plus (nur mit PSSB FW 01.04!!!) Bei einer Kombination PLENTICORE plus mit dem Sony/Murata-Batteriesystem wenden Sie sich bitte an den Service. - Feature: Anpassung des Wintermodes für die AC- Speicherfunktionalität der ersten Ausbaustufe. UI Änderungen - Darstellung: Wechselrichtermodus zum Tiefentladeschutz geändert - Darstellung: Korrekte Übersetzung im Englischen für „Einspeisen“ verwendet (Feed in) Datum (JJJJ.MM.TT): 2019.03.12 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.05.03064 FW-Änderungen: - Feature: AC- Speicher der ersten Ausbaustufe wurden implementiert (Ladung aus dem Hausnetz) - Feature: Umsetzung der Optionen Rundsteuersignale Senden/Empfangen aus PIKO Serie in Digitaleingängen und Energiemanagement umgesetzt - Feature: Neuer Energiezähler KOSTAL Smart Energy Meter (KSEM) ist auswählbar - Optimierung: Umsetzung des automatischen Wintermodes für Nullwattanlagen wurden implementiert - Optimierung: Neue Anlaufsequenz für Außenlüfter wurden implementiert - Optimierung: Download von Logdaten dauerte zu lange und bricht nach 3 Minuten mit Timeout ab - behoben - Darstellung: Wertebereich für Einschalt-/Ausschaltleistung Q von U auf 0 bis 100% ausweitert - Darstellung: Login per Return-Taste nun möglichermöglichen - Darstellung: Batterieauswahl im Einrichtungsassistent wurden aktiviert - Darstellung: Event-Anzeige im Bereich Info im Webserver wurde implementiert - Darstellung: Anzeige der MAC-Adresse auf der Info-Seite wurde implementiert - Darstellung: Portalname zu KOSTAL Solar Portal umbenannt - Darstellung: Button "Batteriemodus zurücksetzen" in den Batterieeinstellungen wurde implementiert - Darstellung: Umbennennung der zuschaltbaren Abschaltgrenzen und Hinweis auf Abhängigkeit von Digitaleingängen - Darstellung: Anzeige der Leistungsreduktion in der WebApp als Absolutwert - Darstellung: Anzeige von Fehlerhaften Eingaben in der WebApp optimiert - Darstellung: Browserabhängiger Umrandungsstärken wurde optimiert - Darstellung: Ausgabe der Fehlermeldung bei Passwort wiederherstellen mit falschem Master Key wurde optimiert - Darstellung: Buttons wurden optimiert - Darstellung: Digitaleingänge - Wirkleistungssteuerungs-Grafik wurde ausgetauscht - Darstellung: Anpassung der Übersetzung - Batteriemenü - Darstellung: Anpassung der Fehlermeldung bei Eingabe eines zu langen Wechselrichternamens - Darstellung: Eingaben von unplausiblen Netzwerkeinstellungen ist im SCB Menü ist nun nicht mehr möglich. - Darstellung: Bugfix: Fehlerhafte Darstellung der Events 5060 und 5061 wurden behoben - Darstellung: Fehlerhafte Übersetzung (Italenisch) im Display korrigiert - Darstellung: Anpassung der dynamischen Eigenverbrauchssteuerung. Aktivierung nur erlaubt wenn ein Leistungsmesser ausgewählt wurde - Bugfix: Fehlende Log-/Portaldaten werden wieder übertragen - Modbus: Ausgabe FW Version wird nun als String ausgegeben - Modbus: Sunspec Adressoffset wurde korrigiert - Modbus Sunspec Ausgabe: Fehlerhafte Scale-Faktoren Datum (JJJJ.MM.TT): 2018.11.12 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.04.02422 Bugfixes: - Wintermode mit BYD Batterie Datum (JJJJ.MM.TT): 2018.11.12 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.04.02090 Features: - Event-Mapping für SunSpec optimiert - ModBus Optimierungen - Menü "Externe Hardwareeinstellungen" mit Abschnitt: Fehlerstrom-Schutzeinrichtungen Kompatibilität RCD Typ A hinzugefügt Bugfixes: - Laufzeitfehler der Kommunikation behoben - Im Parametrierungsbericht fehlten die Werte zum Energiemanagement - Aktive Checkboxen sind in Druckansicht des Reports nun sichtbar - Darstellungsfehler Edge Version 40.15063.674.0 und Firefox behoben - Fehlende Übersetzung des Haftungsausschlusses hinzugefügt --------------------------------------------------------------------------------------- Installation notices To perform the update, you need a network connection between your computer and the inverter. Enter the IP address of the inverter in your browser and after successful login, select in the menu under "Service menu" => "Update". Follow there the instructions. If required, you can save the log data before the update, by downloading it directly from the Webapp or send it to the Piko Solar Portal. After transfer and execution of the update, you must restart the device via the button in the Webapp. Following a successful update, the inverter starts to regular operation mode. If this is not the case, turn the inverter off by disconnecting DC and AC-side for two minutes and then back into operation. Date(JJJJ.MM.TT): 2024.02.21 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.30.12092 Change - Activation of switching overvoltage for LVRT/HVRT - Start-up ramp after islanding detection - Bugfix: Bugfix switch-off sequence PWM / AC relays - Bugfix P(f) overfrequency: Values for static and gradient are not written correctly in the parameterisation report. Date(JJJJ.MM.TT): 2023.09.27 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.29.12038 Change - Bufix: After mains faults, it could happen under certain conditions that an inverter only switched back to the grid after 1 hour. - False triggering of EC5066 corrected. - Correction of display of domestic consumption for values > 38kW Date(JJJJ.MM.TT): 2023.07.10 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.28.10771 Change -Battery system "Dyness Tower" was approved an is selectable in the menu now. Date (JJJJ.MM.TT): 2023.04.21 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.27.09932 Change - Battery systems Wintersun, Pylontech Force H1/H2 and AxiStorage Li SV1/SV2 approved an selectable in the menu. Date (JJJJ.MM.TT): 2023.02.08 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.26.09454 Changes The setting of the active power limitation is now also possible for the system owner. ATTENTION: The system owner is responsible for correctly setting the active power limitation. Your grid operator will provide details of the permissible active power for your system. HINT: We recommend that the installer configures all the settings. Date (JJJJ.MM.TT): 2022.11.28 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.25.09070 (FW01.76) Changes - Bugfix shadow management: It could happen in case of activated shadow management that the battery was not charged or not used until the next day. - Bugfix: It could happen that event code 5076 occurred, which led to short-time shutdowns of the unit. The control algorithm was adjusted accordingly. Date (JJJJ.MM.TT): 2022.09.29 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.24.08775 (FW01.75/PAR03.55) Changes - KOSTAL Energy Meter Series P added as energy meter in the selection menu "KEM-P". - Changed "KEM" in the selection menu to "KEM-C" (Series C) - Compatibility with storage system LG Resu flex - Bugfix: Mobus TCP registers 517, 525, 527 and 586 are filled correctly again. - Bugfix: External battery control is switched off when selecting the battery. - Despite system energy surplus (activated ext. surplus charge), the battery was sometimes not charged when PV energy was not available. This behaviour was corrected and stopped. - Bugfix EC 5076 PC BI: Especially under unfavourable grid conditions, the BI-10-26 could fail to charge the battery in the event of abrupt power changes. (transition to SoC min or to SoC 100%), the inverter could switch off briefly (event code 5076). This behaviour could be intercepted by a functional improvement on the software side. - KEM-C: Bugfix of the house consumption visualisation in case of non-existent DC energy (house consumption at night was not determined and displayed, portal and web app). - Further internal improvements Date (JJJJ.MM.TT): 2022.06.20 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.23.07734 (FW01.70/PAR03.55) Changes - Indication "---" for house consumption in the display, if 0W house consumption is present or no power meter is connected. - Bonjour service supplemented with additional information (Key: ScbWebApi, Value: v1). - Entry "AXITEC" in the battery selection menu changed to "AXIstorage Li SH". - Internal improvements Date (JJJJ.MM.TT): 2022.03.30 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.22.06892 (FW01.65/PAR03.50) Changes - Bugfix 0-Watt limitation - Bugfix "Deselect of intelligent battery control function after update to FW >= 01.60" - RfG requirement sfor Spanin implemented, country set "ES RD647 Type A" - Removal of the selection of obsolete country sets Date (JJJJ.MM.TT): 2022.02.16 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.21.06586 (FW01.60/PAR03.44) Changes - New sleep mode behavior: - When discharging to the configured min. SoC, the battery's relay is opened. - Immediate wake-up from sleep mode and connection of the battery as soon as surplus power is available for charging or charging is requested by external control. - Emergency battery charging: Autom. increase of the delta SoC up to 15% if the battery cannot be charged during a period of bad weather. This minimises emergency charging operations. - Service charge to 100% can be started in the battery settings of the web menu. (Only possible with installer login). - PLENTICORE BI 10/26: CEI 0-16 and CEI 0-21 added in the country settings. Date (JJJJ.MM.TT): 2021.08.05 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.20.05838 Changes - Fix: PLENTICORE BI and Nilar (Contolling of high changes in charge current set values was improved.) Date (JJJJ.MM.TT): 2021.07.02 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.20.05778 Changes - Fix: It was possible to get wrong value in the power flow diagram. Date (JJJJ.MM.TT): 2021.04.19 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.20.05774 Changes - Battery storage systems from BMZ and AXITEC are now supported and selectable in the battery settings menu. - Self-test for Italy CEI 0-21 was improved. - PL 50549-1 frequency parameter 49.0Hz <= f <= 50.05Hz - PL 50549-1 added for PLENTCIORE BI - Actual grid code settings for Switzerland have been implemented: “CH NA/EEA 2020 A2” Date (JJJJ.MM.TT): 2021.04.19 KOSTAL_Update_PLENTICORE_PIKO_IQ_01.19.05650 Changes - Sunspec register corrected (relevant for Varta AC storage) - New battery storage "NNilar Home Box" is compatible - BI 5.5/26 und 10/26: Belgium available as a country setting Date (JJJJ.MM.TT): 2021.01.29 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.18.05218 Changes - AutoUpdate feature is now available. You can choose between “Manual update via fileupload” / “Info about available update” / “Install available updates automatically”. To use this, change the update method under via the webserver under Update. - PLENTICORE BI 5.5/26 und 10/26: New country settings added. Following parameter settings are available now: Land/Country Ländereinstellungen/Display Austria AT TOR Gen. Type A LV Switzerland CH NA/EEA 2014 Germany DE VDE4105 cosphi=1 Denmark DK TF3.3.1 DK1 Type A Denmark DK TF3.3.1 DK2 Type A Spain ES RD1699 RD431 Isl. Spain ES RD1699 RD431 Main Finland FI VJV2018 Type A France FR VFR2019 Greece GR RFG Type A Main Greece GR RFG Type A Islands Latvia LV EN50549-1 2019 Netherlands NL EN50549-1 2019 <11kW Netherlands NL EN50549-1 2019 >11kW Norway NO EN50549-1 2019 Portugal PT EN50438 2013 Portugal PT EN50549-1 2019 Sweden SE EIFS2018-2 Standard EN50438 2013 Standard EN50549-1 2019 Standard G98/1-4 Standard G99/1-6 LV Standard VDE 4100/4105 Date (JJJJ.MM.TT): 2020.11.20 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.17.05075 Changes - Changes in the translations - Changing/saving the "Battery control" menu is only possible for the role of installer - Min. state of charge "Dynamic" was not selectable when "Enable Intelligent Battery Control" was activated Date (JJJJ.MM.TT): 2020.11.05 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.16.05025 Changes - New option external battery control via Modbus (setup only with service code) - New option external battery control via digital inputs (setup only with service code) - Implementation of additional Modbus statistics data points - Implementation Switching option Modbus little to big-endian - Implementation of "time-controlled battery use" (also by end customers) - First Version for PLENTICORE BI 5.5/26 and 10/26 Bugfixes - Display error fan control - Control optimizations - Supplements to meet Modbus Sunspec requirements (read/write) Date (JJJJ.MM.TT): 2020.05.29 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.15.04581 Bugfixes - Correction of Modbus byte order was withdrawn. Date (JJJJ.MM.TT): 2020.05.20 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.15.04529 FW-Changes - Necessary adaptations for BYD Premium Battery HVS 5.1 regarding the battery voltage - Implementation of additional country settings GR RFG Type A Main GR RFG Type A Islands CZ PPDS 2018 <16A CZ PPDS 2018 >16A Bugfixes - Correction of the wrong byte order in the Modbus from CDAB to ABCD - thus float values can be queried according to the official Modbus definition Date (JJJJ.MM.TT): 2020.02.20 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.14.04213.swu UI-Changes - General optimizationsn - Bugfix - Screensaver showed mains power instead of feed-in power - Bugfix - DC power was no longer shown in the display under certain conditions - First Version for PLENTICORE BI 5.5/13 Date (JJJJ.MM.TT): 2019.12.17 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.13.04122.swu FW-Changes - Implementation of more country settings Land/Country Ländereinstellungen/Display Austria AT TOR D4 2016 LV Austria AT TOR Gen. Type A LV Belgium BE C10/11 2019 LV Switzerland CH NA/EEA 2014 Switzerland CH VDE4105 2011 Cyprus CY EN50438 2013 Czech Republic CZ EN50438 2013 Germany DE VDE4105 cosphi=1 Germany DE VDE4105 cosphi(P) Germany DE VDE4105 Q(U) Denmark DK RFG LV DK1 Type A Denmark DK RFG LV DK2 Type A Denmark DK TF3.2.1 2016 Estonia EE EN50549-1 Type A Spain ES RD1699 RD431 Main Spain ES RD1699 RD431 Isl. Finland FI EN50438 2013 Finland FI VJV2018 Type A France FR VFR2014 France FR VFR2019 Greece GR VDE0126 PPC Main Greece GR VDE0126 PPC Islands Italy IT CEI0-21 2017 <11kW Italy IT CEI0-21 2019 <11kW Italy IT CEI0-21 2019 >11kW Jordan JO G59/3-3 LV Jordan JO G83/2 Latvia LV EN50438 2013 Netherlands NL EN50438 2013 Norway NO EN50438 2013 Poland PL EN50438 2013 Poland PL EN50549-1 2019 Portugal PT EN50438 2013 Portugal PT EN50438 2013 3.45kW Portugal PT EN50438 2013 3.68kW Sweden SE EIFS2018-2 Sweden SE EN50438 2013 United Kingdom UK G98/1-3 United Kingdom UK G99/1-4 LV Standard CEI0-21 2017 <11.08kW Standard CEI0-21 2017 >11.08kW Standard CEI0-21 2019 <11.08kW Standard CEI0-21 2019 >11.08kW Standard EN50438 2013 Standard EN50549-1 2019 Standard G59/3-3 LV Standard G83/2 Standard G98/1-3 Standard G99/1-4 LV Standard IEC61727 / 62116 Standard VDE 0126-1-1 Standard VDE 4105 2011 Standard VDE 4105 2018 - Faster Ownconsumption regulations - FW of the KOSTAL Smart Energy Meter will be provide in 2020 Bugfixes - Optimization regarding battery discharges - Optimization of the algorythm of the shadow management with low PV voltages - Optimization in LVRT mode UI-Änderungen - Possibility to start manual fan test - General optimizations Date (JJJJ.MM.TT): 2019.08.09 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.11.03557 Bugfix -Missing display of the choosed country settigs VDE0126, Austria und VDE4105 now avialable The following country settings now avilable Land/Country Ländereinstellungen/Display Austria - AT TOR D4 2016 LV Cyprus - CY EN50438 2013 Czech Republic - CZ EN50438 2013 Germany - DE VDE4105-cosphi=1 Germany - DE VDE4105-cosphi(P) Germany - DE VDE4105-Q(U) Denmark - DK TF3.2.1 2016 Spain - ES RD1699 RD413 Islands Spain - ES RD1699 RD431 Main Finland - FI EN50438 2013 France - FR VFR2014 France - FR VFR2019 Greece - GR VDE0126 PPC Main Greece - GR VDE0126 PPC Islands Italy - IT CEI0-21 2017 <11kW Jordan - JO G83/2 Jordan - JO G59/3-3 LV Latvia - LV EN50438 2013 Netherlands - NL 50438 2013 Norway - NO EN50438 2013 Poland - PL EN50438 2013 Portugal - PT EN50438 2013 Sweden - SE EN50438 2013 Switzerland - CH NAIEEA 2014 Switzerland - CH VDE 4105:2011 United Kingdom - UK G98/1-3 Standard - CEI0-21:2017 <11.08kW Standard - G59/3-3 - LV Standard - G83/2 Standard - G98/1-3 Standard - EN 50438:2013 Standard - IEC61727 / 62116 Standard - VDE 0126-1-1 Standard - VDE 4105:2011 Standard - VDE 4105:2018 Date (YYYYMM.TD): 2019.07.29 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.11.03546 FW changes - Feature: Manual fan test were via display added - Feature: Extension of the modbus register - more battery data - Feature: G98-Trip new configurability for trip function via the web server - Feature: Control of the Q (U) shift factors - Display: Hint on cos phi = 1 with deactivated reactive power - Optimization: Intelligent battery control (yield load forecasting) has been optimized - Bugfix: "Missing Directive display text" is displayed - Bugfix: Auto. Restart after occurring events - Bugfix: Directive / Country setting selection Date (JJJJ.MM.TT): 2019.06.13 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.09.03412.swu Bugfix - Correction of incorrect fan event storages Datum (JJJJ.MM.TT): 2019.04.30 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.07.03318.swu UI - Adjustments license texts Date (JJJJ.MM.TT): 2019.04.26 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.07.03311.swu UI Changes - Renaming/Adition of the country settings Austria - AT TOR D4 2016 LV Cyprus - CY EN50438 2013 Czech Republic - CZ EN50438 2013 Germany - DE VDE4105-cosphi=1 Germany - DE VDE4105-cosphi(P) Germany - DE VDE4105-Q(U) Denmark - DK TF3.2.1 2016 Spain - ES RD1699 RD413 Islands Spain - ES RD1699 RD431 Main Finland - FI EN50438 2013 France - FR VFR2014 France - FR VFR2019 Greece - GR VDE0126 PPC Main Greece - GR VDE0126 PPC Islands Italy - IT CEI0-21 2017 <11.08kW Jordan - JO G83/2 Jordan - JO G59/3-3 LV Latvia - LV EN50438 2013 Netherlands - EN50438 2013 Norway - NO EN50438 2013 Poland - PL EN50438 2013 Portugal - PT EN50438 2013 Sweden - SE EN50438 2013 United Kingdom - UK G98/1-3 Standard - CEI0-21:2017 <11.08kW Standard - G59/3-3 - LV Standard - G83/2 Standard - G98/1-3 Standard - EN 50438:2013 Standard - IEC61727 / 62116 Standard - VDE 0126-1-1 Standard - VDE 4105:2011 Standard - VDE 4105:2018 Features: - Inverter restarts automatically after reset the Country Setting - Integration of the Battery Reset Button in the Webapp - Update of the eventcodelist incl. translations - New battery data via Modbus implemented Battery Type (Modbus Register 588) Manufacturer (Modbus Register 517) ModelName (Modbus Register 525) SerialNumber (Modbus Register 527) WorkACOut (Modbus Register 110) PowerACIn (Modbus Register 280) Bruttokapazität (Modbus Register 529) Status (Modbus Register 104) Firmware (Modbus Register 586) - Updated translations implemented - Display of the battery mode in the Webapp implemented - Optimisation of the Update page - Low-Priority Active power control via Modbus implemented - Bugfixes: - Display of the eventlist - Mobil optimized Date (JJJJ.MM.TT): 2019.03.27 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.05.xxxx FW Changes - Feature: Implementation of Sony/MURATA- Batteriesystems for PLENTICORE plus (only with PSSB FW 01.04!!!) If you would combine PLENTICORE plus with the Sony/Murata-Batterysystem please contact the Service. - Feature: Changes for winter mode for the AC-Storage function UI Changes - Display: Implemented the display mode Deep of discharge protection - Display: Korrection of the wrong translation (Feed in) Date (YYYYMM.TD): 2019.03.12 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.05.03064 FW changes: - Feature: AC memory of the first stage was implemented (charge from the house network) - Feature: Implementation of options Ripple control signals transmission / reception from PIKO series implemented in digital inputs and energy management - Feature: New energy meter KOSTAL Smart Energy Meter (KSEM) can be selected - Optimization: Implementation of the automatic winter mode for zero watt systems has been implemented - Optimization: New startup sequence for outdoor fans has been implemented - Optimization: Download of log data took too long and breaks off after 3 minutes with timeout - fixed - Representation: Value range for switch-on / switch-off power Q extends from U to 0 to 100% - Display: Login via Return key now possible - Appearance: Battery selection in the setup wizard has been activated - Display: Event display in the Info area in the web server has been implemented - Display: Display of the MAC address on the info page has been implemented - Appearance: Portal name renamed to KOSTAL Solar Portal - Display: Button "Reset battery mode" in the battery settings has been implemented - Display: Renaming of the switchable shutdown limits and indication of the dependency of digital inputs - Display: Display of the power reduction in the WebApp as absolute value - Display: Display of incorrect entries optimized in the WebApp - Appearance: browser-dependent border strengths have been optimized - Display: Output of the error message when recovering the password with wrong master key has been optimized - Appearance: Buttons have been optimized - Display: Digital inputs - Active power control graphic has been replaced - Presentation: Translation adjustment - battery menu - Display: Adjustment of the error message when entering an inverter name that is too long - Presentation: Inputs of implausible network settings is now no longer possible in the SCB menu. - Presentation: Bugfix: Incorrect display of events 5060 and 5061 have been fixed - Display: Wrong translation (Italian) corrected in the display - Presentation: Adaptation of dynamic self-consumption control. Activation allowed only if a power meter has been selected - Fix: Missing log / portal data will be transmitted again - Modbus: Output FW version is now output as a string - Modbus: Sunspec address offset has been corrected - Modbus Sunspec output: Incorrect scale factors Date (YYYY.MM.DD): 2018.11.12 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.04.02422 Bugfixes: - Winter mode with BYD battery Date (YYYY.MM.DD): 2018.11.12 KOSTAL_Update_PLENTICORE_plus_PIKO_IQ_01.04.02090 Features: - Event mapping optimized for SunSpec - ModBus Optimisation - Added a new menu "External Hardware Settings" menu with section: Residual current devices compatibility RCD type A Bugfixes: - Runtime error of communication fixed - The parameters for the energy management were missing in the parameterization report fixed - Active checkboxes are now visible in print preview of the report - Display problems Edge Version 40.15063.674.0 and Firefox fixed - Missing translation of the disclaimer fixed